How to clean a dripper ?

Simply unscrew the tank holder and replace the old sprayer with a new one. Once you have mounted and soaked your new e-liquid, you can reattach the base. It is then possible to fill your clearo, either from above or below, depending on the model.

Why did my resistance burn out quickly?

Improperly adjusted battery. Each resistor has a power range (expressed in watts) that can be adjusted for optimal use. Below the recommended wattage, the resistor may leak. If used above, it evaporates the liquid too quickly and gives that familiar burnt taste.

How to avoid damaging your resistance? To prolong the life of your heating element, it is also important to respect a 10 second pause between each breath. This allows the resistor to cool down and not to overheat. Overheating is a common cause of premature wear and tear.

How to make an electronic cigarette resistance last?

How to extend the life of your resistor?

• Systematically start a new resistor;
• Vaper e-liquids richer in PG than VG ;
• Set the power of your e-cigarette correctly;
• Do not chain weld (and take breaks between each steam output);

What is the life of an electronic cigarette resistance?

As an average, it is fair to say that changing the resistor every 15 days when used daily is a common frequency.

How to keep a resistor?

However, there is one sure thing you can do to maintain the resistance of your rebuildable: by changing the cotton every 2-3 days and brushing it with a wire brush, you will already remove a lot of dirt and avoid splashes. e-liquid residues that were not...

How not to burn out your resistance?

Vegetable glycerin improves the vapor and its density. Many VG are not compatible with all clearomizers because this is what makes a liquid "fat". Thus, depending on the openings and capillarity - "cotton density" - of your resistance, fatty e-liquids will have trouble flowing effectively.

How to properly soak your resistance?

Soaking the cotton means starting to resist e-cigarettes. When your resistor is new, the cotton is really dry. By putting drops on it, you are simply preventing it from burning when you first heat it. You'll just need to check that all the cotton is ground up.

How to start your resistance?

Priming your resistor is nothing more or less than soaking the cotton that surrounds the wire that heats up and allows it to evaporate. When your resistor is new, the cotton is really dry. By putting drops on it, you simply prevent it from burning when you first heat it.

How not to burn its resistance? Vegetable glycerine improves the steam and its density. Many VG are not compatible with all clearomizers because this is what makes a liquid "fat". Thus, depending on the openings and capillarity - "cotton density" - of your resistance, the fatty e-liquids will have difficulty in circulating effectively.

How do you know if the resistance is dead?

In short: how do you know if your resistance is dead?

• You feel a jolt.
• Your steam is less dense.
• Your steam has less flavor.
• Your resistance turns black.
• You have been mating with the same resistance for over 20 days.
• It is louder than usual.

How do I know if I need to change the resistor?

The frequency of change varies, but the clues are simple: when the loss or change in taste due to long-term use of the resistance becomes really noticeable, it's time to change it.

How to know when to change the resistance of an electronic cigarette?

In general, the resistance should be changed every 2-3 weeks or every 15-20 charges, but this depends primarily on the frequency of use, the quality of the material and the e-liquid used.

Why do I inhale E-liquid?

A clogged or flooded resistor can cause liquid to rise in an electronic cigarette. Check the amount of propylene glycol and vegetable glycerin in your e-liquid. High levels of propylene glycol can make your e-liquid a bit overdone.

Why is my e-liquid too liquid?

2 main factors explain an e-liquid too liquid: The presence of water or alcohol in the composition of the bottle. Too much propylene glycol in its base pg vg.

Why do I have liquid in my mouth when I Vapote?

A vapoteur used with too little power will not heat your resistor enough, which will inevitably lead to a new overflow of liquid. It will be the same if your resistance heats up too much and too fast.

How to clean Vaporesso?

A simple, slightly damp cloth is more than enough to clean your box. You can possibly use alcohol to clean the sensitive parts. During this cleaning, do not forget the needle 510 (the part where the clearomizer is screwed) which can help you with a cotton swab.

How do I clean Vaporesso? Moisten a microfiber cloth or paper towel with alcohol and wipe the target areas until they are clean. Then wipe and rinse with warm water. You can also use a jewelry cleaning machine to remove stubborn deposits, if necessary.

How to reset an electronic cigarette?

C - The battery of my e-cigarette does not work 2) Remember to unlock the battery by pressing 5 times in a row. 5 consecutive presses make ON / OFF the battery. You press 5 times, it turns on, you press 5 more times and it turns off.

Why my electronic cigarette does not smoke?

If your e-cigarette does not produce enough vapor, check the amount of e-liquid, the resistance value or the battery charge. In addition, the condition of the device may be at fault. Indeed, the battery or the resistance may have deteriorated over time.

When I pull on my electronic cigarette?

An electronic cigarette that sizzles? It is normal! The crackling that you hear when you press the switch on your e-cigarette is actually due to the rise in temperature of the liquid. The resistance heats up under the effect of the battery and allows the e-liquid to reach the evaporation phase.

How to clean a VAPE ?

It must be cleaned every two days. To do this, simply blow into the nebulizer to remove the remains of e-liquid. Then wash the wire with a damp cloth. This simple operation will extend the life of the device and prevent the steam from taking an unpleasant taste.

How to clean a VAPE pod?

To do this, you must detach the cartridge from the battery and then remove the resistor if possible. Then place the container under water and wipe it with a dry cloth. Reassemble it, refill with your favorite e-liquid and you can steam again!

How to clean an electronic cigarette to change its taste?

To clean, first run the spray and drip tip under warm water. Then dry the sprayer with a cloth or paper towel. You can also let it air dry.

How to clean the Vaporesso Clearomizer?

Why clean your drip?

• Step 1: Remove the drip tip from the cleaner.
• Step 2: Pour a drop of dishwashing liquid into the drip type.
• Step 3: Rinse thoroughly with clean water.
• Step 4: Dry it with a dry cloth.
• Step 5: Blow in to remove the last of the deposits.

How to clean your Clearomizer ?

Cleaning the atomizer is easier than maintaining the atomizer. You just need to blow in the cleaning agent from time to time and wash it thoroughly if you change the e-liquid. To do this, rinse it with a little clear water and let it dry for 24 hours.

How to clean the tip of the electronic cigarette?

Use a cotton swab to get into the hole and remove the dust inside. Dampen it lightly with white vinegar or alcohol, then clean it. If the USB port on your e-cigarette is not properly maintained, debris can get stuck, build up and block the charge.

How to disassemble an atomizer?

To separate the two elements of the electronic cigarette, simply unscrew the ato from the modbox connector. Then open the base of the atomizer. Take the bottom part of the ato between your fingers and twist it off. This disassembles the rebuilt atomizer.

How to repair an atomizer ? How to repair a defective airflow by yourself?

• Remove the atomizer from the box;
• Pull the airflow or use the clamp as a lever to lift the mechanism;
• Play with the mechanism to loosen or replace the ring that is out of its usual place;

How to remove no Atomizer?

An improperly or overly tight vape coil can also cause the message No atomizer, Atomizer Short or No atomizer found on the electronic cigarette to be displayed. If this is the case, unscrew the atomizer and replace the resistor without over tightening.

How to repair an electronic cigarette?

Unfortunately, everything electronic has a limited life span. The resistor, for example, can not be "repaired", when it stops working, it must be changed. The same goes for the switch, like the button of an electronic cigarette.

Why I can not pull on my electronic cigarette?

If you can not inflate your e-cigarette or if your vaporizer is clogged, check the drip tip. Indeed, if you are used to put your vape in your pocket or bag, dirt can settle inside and clog it.

How to remove a Clearomizer ?

It is also possible to unscrew the drip type of the clearomizer. The drip type is the mouthpiece through which the vapoteur inhales steam. To remove it, turn it slightly to the side. It is unscrewed, like all spare parts of clearomizer.

How to unscrew a blocked atomizer?

Freezer method This method consists of leaving your mode or atomizer in the freezer for about thirty minutes and then trying to loosen the parts by turning. I also invite you to tap the object lightly on the side to try to unblock the wire.

How to open an atomizer ?

To be able to loosen the atomizer, take a thin cotton swab. Try to tip it between mod and ato to remove some dust. You can also put on gloves to make the atomizer a little more. Your fingers will no longer slip and it will be easier to unscrew the device from the box.

How to open an atomizer ?

To be able to loosen the atomizer, take a thin cotton swab. Try to tip it between mod and ato to remove some dust. You can also put on gloves to make the atomizer a little more. Your fingers will no longer slip and it will be easier to unscrew the device from the box.

How to unlock an electronic cigarette?

E-cigarette locked: switch button, it saves Before panicking, make sure you have turned on and unlocked your electronic cigarette. To do this, simply press three or five times very quickly on the switch button of your mode (this varies by model).

How to open a blocked atomizer?

Freezer method This method consists of leaving your mode or atomizer in the freezer for about thirty minutes and then trying to loosen the parts by turning. I also invite you to tap the object lightly on the side to try to unblock the wire.

How to remove the liquid electronic cigarette?

You can start by soaking the end of the fabric in warm water. Unlike cold water, warm water makes it easier to remove stubborn stains and other debris. You'll need to go through the tank several times with a cloth.

How to clean the mouth of an electronic cigarette? Use a cotton swab to get into the hole and remove the dust inside. Moisten it lightly with white vinegar or alcohol, then clean it. If the USB port on your e-cigarette is not properly maintained, debris can get stuck, build up and block the charge.

How do you remove the taste from your food?

To clean, first run the spray and drip tip under warm water. Then dry the sprayer with a cloth or paper towel. You can also let it air dry.

How to soften a taste of electronic cigarette?

Use a neutral, fragrance-free e-liquid to dilute the base and reduce odors; Add a few drops of fresh or light flavor to balance the strength of the flavor (mint or acidic fruit flavors can offset an overly sweet or strong e-liquid).

How to drain the taste of a ce?

To empty the tank, it is important to open the largest possible opening. To do this we advise you to go through the bottom of the clearomizer. In general, access to the tank cores is wider. To do this, simply unscrew the base of the tank.

How to empty the liquid from my electronic cigarette?

To empty the tank, it is important to open the largest possible opening. To do this we advise you to go through the bottom of the clearomizer. In general, access to the tank cores is wider. To do this, simply unscrew the base of the tank.

When to put back the E-liquid ?

When to add a little e-liquid? Don't wait until your e-liquid cartridge is completely exhausted to refill it! If you use your electronic cigarette when the e-liquid is empty, you risk burning the atomizer. It is therefore ideal to fill it when it is about 0.4 ml.

How to clean the tank of its electronic cigarette?

If you have a one-piece e-cigarette and the cartridge does not fall apart, follow these steps: Use a cotton swab or alcohol to clean the cartridge. Indeed, the battery being in the same block, rinsing with water is totally prohibited.